Ford 2003 Taurus Скачать руководство пользователя

Страница: 20 / 47

PINPOINT TEST H: INCORRECT/ERRATIC DIRECTION OF AIR FLOW FROM OUTLET — MANUAL CLIMATE CONTROL

GO to Pinpoint Test K

G11 CHECK THE RCC MODULE FUNCTIONS

Press each function button and observe the display.

Does the RCC perform and display any functions?

Yes

INSTALL a new RCC module. TEST the system for normal
operation.

GO to

G12

G12 CHECK THE VOLTAGE TO THE RCC

Ignition OFF.

Disconnect: RCC C228.

Ignition ON.

Measure the voltage between ground and:

RCC module C228 pin 11, circuit 729 (RD/WH).

RCC module C228 pin 10, circuit 298 (VT/OG).

Are the voltages greater than 10 volts?

Yes

GO to

G13

REPAIR the affected circuit. TEST the system for normal
operation.

G13 CHECK THE GROUND CIRCUIT TO THE RCC

Ignition OFF.

Measure the resistance between the RCC module C228 pin 8, circuit 570 (BK/YE) and ground.

Is the resistance less than 5 ohms?

Yes

INSTALL a new RCC module. TEST the system for normal
operation.

REPAIR circuit 570 (BK/YE) for an open. TEST the system for
normal operation.

Test Step

Result / Action to Take

H1 CHECK THE AIR FLOW IN EACH SETTING

Ignition ON.

With the engine running, set the blower motor speed to maximum.

Check the air flow in each function selector switch setting at engine idle and under acceleration.

Is the air flow from only the defroster outlets in each function selector switch setting?

Yes

GO to

H10

H2 CHECK FOR VACUUM AT THE CHECK VALVE

Disconnect the vacuum check valve vacuum source line and check for manifold vacuum and connect the vacuum pump.

Is manifold vacuum present at the check valve vacuum source line?

Yes

GO to

REPAIR or INSTALL a new check valve
vacuum source line. TEST the system for
normal operation.

H3 CHECK THE VACUUM CHECK VALVE FOR BLOCKAGE

Reconnect the vacuum source line to the vacuum check valve.

Disconnect the vacuum reservoir line and the function selector switch source vacuum line from the vacuum check valve one at
a time.

Yes

GO to

INSTALL a new vacuum check valve
(19A563). TEST the system for normal
operation.

Page 20 of 47

2003 Taurus/Sable Workshop Manual

11/22/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS3H/~MUS~LEN/19/...

Содержание 2003 Taurus
















































Результаты поиска

Содержание 2003 Taurus

Отзывы:

Похожие инструкции для 2003 Taurus

Бренды по названию

Популярные бренды

Ford 2003 Taurus, Руководство по ремонту

Результаты поиска

Содержание 2003 Taurus

Отзывы:

Похожие инструкции для 2003 Taurus

Бренды по названию

Популярные бренды