background image

  

Are the resistances less than 5 ohms?

 

 

A8 CHECK CIRCUIT 250 (OG) AND 249 (DB/LG) FOR A SHORT TOGETHER

 

Measure the resistance between RCC module C228 pin 22, circuit 250 (OG) and RCC module C228 pin 21, 
circuit 249 (DB/LG).  
 

  

Is the resistance less than 5 ohms?

 

Yes

 

INSTALL a new door actuator. REFER to 

Section 412-04

TEST the system for normal operation.  
 

No

 

REPAIR circuit 250 (OG) and circuit 249 (DB/LG) for a 
short together. TEST the system for normal operation.

 

A9 CHECK THE FEEDBACK POTENTIOMETER TOTAL RESISTANCE

 

Ignition OFF.  

Measure the resistance between RCC module C228 pin 5, circuit 436 (RD/LG) and RCC module C228 pin 20, 
circuit 438 (RD/WH).  
 

  

Is the resistance between 5,000 and 6,000 ohms?

 

Yes

 

GO to 

A12

.  

 

No

 

If the resistance is greater than 6,000 ohms, GO to 

A10

 . 

If the resistance is less than 5,000 ohms, GO to 

A11

 .

 

A10 CHECK CIRCUITS 436 (RD/LG) AND 438 (RD/WH) FOR AN OPEN

 

Disconnect: Temperature Blend Door Actuator C289.  

Measure the resistance between RCC module C228 pin 5, circuit 436 (RD/LG) and the temperature blend door 
actuator C289 pin 6, circuit 436 (RD/LG). Measure the resistance between RCC module C228 pin 20, circuit 438 
(RD/WH) and the temperature blend door actuator C289 pin 5, circuit 438 (RD/WH).  
 

  

Are the resistances less than 5 ohms?

 

Yes

 

INSTALL a new temperature blend door actuator. REFER 
to 

Section 412-04

. TEST the system for normal operation. 

 
 

No

 

REPAIR the affected circuit for an open. TEST the system 
for normal operation.

 

A11 CHECK CIRCUIT 438 (RD/WH) FOR A SHORT TO CIRCUIT 436 (RD/LG)

 

Disconnect: Temperature Blend Door Actuator C289.  

Measure the resistance between RCC module C228 pin 20, circuit 438 (RD/WH) and RCC module C228 pin 5, 
circuit 436 (RD/LG).  
 

  

Is the resistance greater than 10,000 ohms?

 

Yes

 

INSTALL a new temperature blend door actuator 
(19E616). REFER to 

Section 412-04

. TEST the system 

for normal operation.  
 

No

 

REPAIR circuits 438 (RD/WH) for a short to circuit 436 
(RD/LG). TEST the system for normal operation.

Page 10 of 47

2003 Taurus/Sable Workshop Manual

11/22/2011

http://www.fordtechservice.dealerconnection.com/pubs/content/~WS3H/~MUS~LEN/19/...

Содержание 2003 Taurus
















































Отзывы: