Ford 2001 Ranger Скачать руководство пользователя страница 79

Страница: 79 / 1218

100-09-25

Powertrain Diagnostic Routines Identification

DIAGNOSIS AND TESTING (Continued)

ROUTINE 8: VEHICLE DOES NOT CHARGE (LEAD ACID VEHICLES)

TEST STEP

ACTION TO TAKE

•

Is there a temperature difference of greater than 7

C (13

F) between

No =

CONNECT the vehicle to

the temperature sensor that is below 5

C (41

F) and the other

the power control station

temperature sensors?

(PCS) to warm the traction

battery to a temperature

greater than 7

C (45

F).

MONITOR the TMPSEN

PIDs while the vehicle is

connected to the PCS. If the

temperature of the battery

temperature sensor that was

less than 5

C (41

F) does

not increase, GO to 8-11.

8-10 CHECK BATTERY TEMPERATURE SENSOR

(UNDERTEMPERATURE CONDITION)

•

Remove the traction battery and connect Traction Battery High-Voltage

Yes =

REPLACE the BCM.

Lockout and Diagnostic Tool to the traction battery high-voltage two-pin

REFER to

Section

C3994M.

414-03A

•

Connect Traction Battery High Voltage Service Cord to traction battery

No =

REPLACE the battery

support tray in-line C1935F and in-line C1935M.

temperature sensor in

question.

WARNING: The traction battery contains high-voltage

components and wiring. High-voltage insulated safety gloves and face

shield must be worn when carrying out the following steps. Failure to

follow this warning may result in severe personal injury or death.

•

Connect Traction Battery Low Voltage Service Cord to traction battery

support tray in-line C1939F and in-line C1939M.

•

With key OFF, disconnect the battery temperature sensor in question and

one of the other temperature sensors.

•

Connect jumper wires between the connector for the temperature sensor

in question and the known good temperature sensor that was

disconnected.

•

With key ON, monitor battery control module (BCM) PIDs TMPSEN1,

TMPSEN2, TMPSEN3, and TMPSEN4.

•

Does the TMPSEN PID that indicated less than 5

C (41

F) still

indicate less than 5

C (41

F)?

8-11 CHARGE TRACTION BATTERY TO FULL STATE OF

CHARGE (SOC)

•

Disconnect and reconnect the 12-volt auxiliary battery negative cable.

Yes =

REPEAT this test step. The

traction battery has not

reached full SOC.

NOTE: If the EMG PO PID indicates ENABLE after pressing the

No =

System OK.

START button on the power control station (PCS), GO to 8-13.

•

Charge the traction battery to full SOC.

•

With key OFF and vehicle on-charge, monitor BCM PIDs EMG PO

and BCM OP.

•

Does the BCM OP PID still indicate 96 (no charge-EPO detected)?

8-12 CHECK EMERGENCY POWER OFF (EPO) SIGNAL TO

BATTERY CONTROL MODULE (BCM)

•

Remove the traction battery and connect Traction Battery High-Voltage

Yes =

GO to 8-13.

Lockout and Diagnostic Tool to the traction battery high-voltage two-pin

C3994M.

(Continued)

2001 Ranger EV, 01/2001

Содержание 2001 Ranger



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 2001 Ranger

Отзывы:

Бренды по названию

Популярные бренды

Ford 2001 Ranger, Руководство пользователя

Результаты поиска

Содержание 2001 Ranger

Отзывы:

Бренды по названию

Популярные бренды