Ford 2001 Crown Vic Скачать руководство пользователя

Страница: 162 / 248

When driving with the temporary spare tire

do not:

•

exceed 80 km/h (50 mph) under any circumstances

•

load the vehicle beyond maximum vehicle load rating listed on the
Safety Compliance Label

•

tow a trailer

•

use tire chains

•

drive through an automatic car wash, because of the vehicle’s reduced
ground clearance

•

try to repair the temporary spare tire or remove it from its wheel

•

use the wheel for any other type of vehicle

Tire change procedure

To prevent the vehicle from moving when you change a tire, be
sure the parking brake is set, then block (in both directions) the

wheel that is diagonally opposite (other side and end of the vehicle) to
the tire being changed.

If the vehicle slips off the jack, you or someone else could be
seriously injured.

1. Park on a level surface, activate
hazard flashers and set parking
brake.

2. Place gearshift lever in P (Park),
turn engine OFF and block the
diagonally opposite wheel.

HOOD

Roadside emergencies

162

Содержание 2001 Crown Vic

























































































































































































































































Результаты поиска

Содержание 2001 Crown Vic

Отзывы:

Похожие инструкции для 2001 Crown Vic

Бренды по названию

Популярные бренды

Ford 2001 Crown Vic, Руководство пользователя

Результаты поиска

Содержание 2001 Crown Vic

Отзывы:

Похожие инструкции для 2001 Crown Vic

Бренды по названию

Популярные бренды