Ford 2001 Crown Vic Скачать руководство пользователя

Страница: 133 / 248

3. Locate the correct anchor for the
selected seating position.

4. Open the tether anchor cover.

5. Clip the tether strap to the
anchor as shown.

If the tether strap is clipped
incorrectly, the child safety

seat may not be retained properly
in the event of a collision.

6. Refer to the

Installing child

safety seats in combination lap and shoulder belt seating positions

section of this chapter for further instructions to secure the child safety
seat.

7. Tighten the child safety seat tether strap according to the
manufacturer’s instructions.

If the safety seat is not anchored properly, the risk of a child
being injured in a collision greatly increases.

Seating and safety restraints

133

Содержание 2001 Crown Vic

























































































































































































































































Результаты поиска

Содержание 2001 Crown Vic

Отзывы:

Похожие инструкции для 2001 Crown Vic

Бренды по названию

Популярные бренды

Ford 2001 Crown Vic, Руководство пользователя

Результаты поиска

Содержание 2001 Crown Vic

Отзывы:

Похожие инструкции для 2001 Crown Vic

Бренды по названию

Популярные бренды