Force Computers PENT/CPCI-721 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 126

background image

Hardware Upgrades and Accessories

Installation

2 - 12

PENT/CPCI-721

Two IDE devices can be connected externally to the secondary IDE port
via the CompactPCI connector J5 in combination with the IOBP-
CPU720.

Note: The IOBP-CPU720 is especially designed for the base board
variants of the PENT/CPCI-72x. Do not use any other I/O panel on the
Base-720.

IOBP-IO720

Force Computers offers an IOBP-IO720 panel which is plugged into the
CompactPCI backplane from its rear. The panel enables easy connection
to the I/O signals of an I/O board which are available on the I/O
board’s J5 connector.

Caution

• The IOBP-IO720 is especially designed for the I/O board variants

of the PENT/CPCI-72x. Do not use any other I/O panels on the I/O-
721.

• Never connect SCSI devices to both SCSI connectors on board the

IOBP-IO720. Decide whether you want to use 16-bit or 8-bit SCSI.

• Never connect devices to both connectors on board the IOBP-

IO720 which carry the PMC user I/O signals. Decide whether you
want to use the full or only the partial range of PMC 2 user I/O sig-
nals.

The I/O panel includes an on-board flat cable and industry standard
connector for the PMC user I/O signals and for the SCSI signals.

PMC Module

The I/O-721 provides one PMC slot. If the I/O-721 is shipped without
the modules installed, the front panel cutouts are covered by blind pan-
els to ensure proper EMC shielding.

«
...
50
51
52
53
54
...
»

Содержание PENT/CPCI-721































































































































Отзывы:

Нет отзывов

Похожие инструкции для PENT/CPCI-721

Montego II Quadzilla

Бренд: Voyetra Turtle Beach Страницы: 56

Бренд: Ask Страницы: 13

Бренд: ATI Technologies Страницы: 50

DF PROFINET IO PCI

Бренд: Kunbus Страницы: 7

Бренд: Nordic ID Страницы: 12

Бренд: Nordic ID Страницы: 19

Бренд: Diablotek Страницы: 1

Бренд: Diablotek Страницы: 1

Бренд: Diablotek Страницы: 1

Бренд: PowerWalker Страницы: 5

Бренд: Diablotek Страницы: 1

Бренд: Z-Com Страницы: 20

Бренд: Kantech Страницы: 26

Бренд: IDTECK Страницы: 24

Бренд: Ratoc Systems Страницы: 19

Бренд: Ratoc Systems Страницы: 26

Бренд: SWEEX Страницы: 4

Бренд: MEGAlink Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды