Force Computers PENT/CPCI-721 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 126

background image

Introduction

Board Expansions

PENT/CPCI-721

1 - 7

Board Expansions

The PENT/CPCI-721 is a 6U CompactPCI board based on an Intel Pen-
tium CPU and consists of the Base-721 and I/O-721. It is two Compact-
PCI-slots wide and operates at 33 MHz PCI bus frequency.

The PENT/CPCI-721 is designed to run with Windows NT Version 4.0.

Figure 2:

PENT/CPCI-721 with I/O-721

PENT/CPCI-721

The PENT/CPCI-721 provides several expansions which will be
described in the following subsection. The PENT/CPCI-721 provides a
one-slot front panel and has no carrier board. Therefore there are no
Base-721 factory options for floppy drive or hard-disk drive and the
LPT1 port is not available on the front panel.

Figure 3:

PENT/CPCI-721

1 PMC module (user option)

I/O-721 in 2nd slot

MEM-720L

PENT/CPCI-721 in 1st slot

MEM-720U

VGA-IO720-4

IOBP-IO720

IOBP-

CPU720

CompactPCI

To CompactPCI

MEM-720L

PENT/CPCI-721 in 1st slot

Front panel

1 slot high

MEM-720U

To I/O-721

in 2nd slot

«
...
33
34
35
36
37
...
»

Содержание PENT/CPCI-721































































































































Отзывы:

Нет отзывов

Похожие инструкции для PENT/CPCI-721

Бренд: Nedap Страницы: 40

Бренд: Hama Страницы: 36

Бренд: Intergraph Страницы: 26

NI Vision NI PCI-1424

Бренд: National Instruments Страницы: 28

Бренд: ATCOM Страницы: 15

Бренд: Bewator Страницы: 2

Бренд: Clas Ohlson Страницы: 4

Бренд: Danpex Страницы: 3

Бренд: Ableconn Страницы: 31

Бренд: Neousys Technology Страницы: 44

Бренд: Farpointe Data Страницы: 2

CONEKT PCR-620L-OSDP

Бренд: Farpointe Data Страницы: 2

Бренд: GE Страницы: 33

Бренд: GE Страницы: 53

Бренд: IDTECH Страницы: 15

Бренд: Bplus Technology Страницы: 12

Бренд: Unigraf Страницы: 11

N-FXE-02 Series

Бренд: Transition Networks Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды