FOR-A USF-101MDX4-12G страница 5 Скачать руководство пользователя

Страница: 5 / 48

8-2-3. Setting Command List (Other) sent from Command Systems ..........................................33

8-3. Command Details (Audio) .........................................................................................................34

8-3-1. Audio Polarity Setting Commands .....................................................................................34

8-3-2. Audio Mapping Setting Commands ...................................................................................34

8-3-3. Audio Master Gain Setting Commands .............................................................................34

8-3-4. Audio Gain Setting Commands .........................................................................................35

8-3-5. Audio Master Delay Setting Commands ............................................................................35

8-3-6. Audio Delay Setting Commands ........................................................................................35

8-4. Command Details (Other) .........................................................................................................36

8-4-1. Power On Commands .......................................................................................................36

8-4-2. Event Load Commands .....................................................................................................36

8-4-3. Event Save Commands .....................................................................................................36

8-4-4. Payload ID Setting Commands ..........................................................................................36

8-4-5. Status Request Commands (Audio 1) ...............................................................................36

8-4-6. Status Request Commands (Audio 2) ...............................................................................37

8-4-7. Status Request Commands (Payload ID) ..........................................................................37

8-5. Command Responses ...............................................................................................................38

8-6. Status Messages from USF-101MDX4/8-12G module .............................................................38

8-6-1. Status Message (Audio 1) .................................................................................................39

8-6-2. Status Message (Audio 2) .................................................................................................40

8-6-3. Status Message (Payload ID) ............................................................................................40

8-7. Command Flow Description ......................................................................................................41

8-7-1. Checking USF-101MDX4/8-12G Module Start-up .............................................................41

8-7-2. Changing USF-101MDX4/8-12G Module Setting (Audio Gain) ........................................41

8-7-3. Reporting USF Module Status Change .............................................................................41

9. About SNMP .......................................................................................................................................42

10. Specifications and Dimensions ........................................................................................................45

10-1. Specifications (USF-101MDX4-12G) ......................................................................................45

10-1. Specifications (USF-101MDX8-12G) ......................................................................................46

10-2. External Dimensions (USF-101MDX4-12G) ...........................................................................47

10-3. External Dimensions (USF-101MDX8-12G) ...........................................................................48

Содержание USF-101MDX4-12G

















































Результаты поиска

Содержание USF-101MDX4-12G

Отзывы:

Похожие инструкции для USF-101MDX4-12G

Бренды по названию

Популярные бренды

FOR-A USF-101MDX4-12G, Руководство по эксплуатации

Результаты поиска

Содержание USF-101MDX4-12G

Отзывы:

Похожие инструкции для USF-101MDX4-12G

Бренды по названию

Популярные бренды