FOR-A USF-101MDX4-12G страница 18 Скачать руководство пользователя

Страница: 18 / 48

Item

Default

Setting

Description

Group
Alignment

Disable

Enable
Disable

Selects whether to perform auto phase
adjustment among each SDI input audio
group.

Enable

: Performs auto adjustment.

Disable

: Performs no auto adjustment

(Normal setting).

Demultiplexer
Clock

Auto

Auto
Sync SDI
Audio Clock

Selects the audio de-embedding method for
HD-SDI input.

Auto

: Uses the audio clock phase data in the

SDI input to de-embed audio
independently for each group
(Synchronous or asynchronous
de-embedding). If the audio phase data
incorrect or de-embedded audio has
noticeable jitter, audio channels in all
groups are de-embed synchronously.

Sync SDI

: Synchronously de-embeds audio

channels in all groups without using the
audio clock phase data.

Audio Clock

: Uses the audio clock phase

data in the HD-SDI input to de-embed
audio independently for each group
(Synchronous or asynchronous
de-embedding).

Error Sensing

Normal

Disable
Normal
Sensitive

Selects the input audio error detection mode
used for

Error Fade

below.

Disable

: Detects no errors for Error Fade.

Normally do not use.

Normal

: Detects SDI signal switching, ADP

(Audio Data Packet) change and DBN
(Data Block Number) switching as Error
Fade errors.

Sensitive

: Adds channel status change and

EDP (Extended Data Packet) change
(SD-SDI only) to those described above
as Error Fade errors.

Error Fade

Disable

Disable
Enable

Disable

: Passes through input audio without

using any effects.

Enable

: Fades out and mutes audio when an

input error is detected and fades in when
recovered.

Audio Polarity
Ch.1-16

Normal

Normal
Invert

Selects the channel polarity.
Selecting

Invert

inverts the audio channel

polarity.

Содержание USF-101MDX4-12G

















































Результаты поиска

Содержание USF-101MDX4-12G

Отзывы:

Похожие инструкции для USF-101MDX4-12G

Бренды по названию

Популярные бренды

FOR-A USF-101MDX4-12G, Руководство по эксплуатации

Результаты поиска

Содержание USF-101MDX4-12G

Отзывы:

Похожие инструкции для USF-101MDX4-12G

Бренды по названию

Популярные бренды