background image

Maestro 400 Series Top Kit for Lancer

Installation

1.   Install Lancer ice dispenser according to manufacturer’s specifi cations.

 

 Note:

 We recommend that the dispenser back be mounted at least 1" (26mm) from wall to allow water, drain 

and electric lines from top mount ice machines to be concealed behind dispenser.

2.   Disconnect power to dispenser.

3.   Remove front panel/merchandiser from the dispenser.

4.   Adjust the agitation timer located on Lancer PC board to 1 second on (Fig. 1.1) – 2 1/2 hours off (Fig. 1.2).

PRESS IN ON 

THIS SIDE  TO  

TURN SWITCH 

ON. 

SWITCH 

ON 

SWITCH 

OFF 

PRESS IN ON 

THIS SIDE  TO  

TURN SWITCH 

OFF . 

R OCKER 

SWITCHES 

(VIEW LOOKING 

DO WN) 

SIDE  VIEW 

SIDE  VIEW 

OFF 

SWITCH 

NUMBER 

A GIT A TION FREQUENCY 

NO A

 GIT

 A TION

 

10

 MINU

TE

20 M

INUTES 

30 

MINUTES 

40 MIN

UTES 

50 MI

NU

TES 

60 MINUT

ES 

70

 MI

NU

TES 

80 MINUT

ES 

90

 MIN

UTES

 

100 

MIN

UTES 

11

0 MIN

UTES 

120

 MIN

UTES

 

130 MINUTES 

140

 MI

NU

TES 

150 

MINUTE

SWITCH 

NUMBER 

A GIT A TION  TIME 

1 SE

COND 

2 SEC

ONDS 

3 SEC

ONDS 

4 SECON

DS 

X = ON 

O = OFF 

1

2

Fig. 1

Содержание Maestro Chewblet 400 Series





















Отзывы: