background image

14

Horizon Elite 710/1010/1410

 

 

HARMONY • RIDE Technology

6. 

Internal Connections

Air-cooled ice machines – follow steps 6.1 through 6.5.
Water-cooled ice machines – follow steps 6.6 through 6.12.

6.1 

Ice transport tube

6.2 

Water solenoid, shut-off valve, and 

potable water line options

6.2.1 

If water solenoid is already mounted to 

evaporator:

1.  Insert potable water line into shut-off valve.

6.2.2 

If this is an undercounter installation:

1.  Mount water solenoid atop evaporator 

and locate the shut-off valve 

inside

 the 

machine. Insert potable water line into 
shut-off valve.

6.2.3 

If water solenoid is not mounted and 

machine will not be installed undercounter:

1.  Mount water solenoid to inside rear (upper 

right corner) of docking assembly using 
one screw. 

2.  Insert potable water line into shut-off 

valve - locate the shut-off valve 

outside

 the 

machine.

3.  Insert outgoing line from shut-off valve into 

push-in connection of water solenoid.

 

§

Slide ice machine into docking assembly 

ensuring 

that drain tube is fully seated on barbed drain fitting

 

.

 

§

Insert ice transport tube all the way into coupling 
and tighten nut firmly 

.

6.3 

Power cord

6.4 

Power cord

 

§

Remove twist tie.

 

§

Carefully pass cord through opening and plug into 
wall outlet.

 

§

For H_E units, install a suitable plug.

 

§

Position plate into opening and secure with 
supplied screw.

 WARNING!

Plate must be securely installed to ensure proper 
equipment ground.

Содержание Horizon Elite HCC1010AHS

























Отзывы: