Foerster TAK5-CH1-25 Скачать руководство пользователя страница 67

Страница: 67 / 226

Setup

4.8.2

IFS-concentrate stations

Here you can configure the concentrate station(s). Up to four

concentrate stations per automatic feeder can be connected.

Address

In the line

allocation

select the concentrate station which has to

be allocated to the IFS-concentrate control.

Address

The IFS (concentrate feeder) is part of the CAN-bus system.

Therefore it requires an address for clear identification purposes.

Type

Here you can select the concentrate feeder type.

Search?

Please refer to the previous chapter

IFS-feed controls

Note:

If you have activated the

search mode

by mistake,

repress the red button. The search mode will be

terminat-

stations

feed

concentrate

animal scales

<IFS-C 1>

allocation:[station 1]

address: 51

type: standard

search?

Note:

Within a CAN-bus system an address can be allo-

cates only once. The default addresses are the following:

IFS-C 1 (= concentrate station 1): address 51

IFS-C 2 (= concentrate station 2): address 52

...

IFS-C 8 (= concentrate station 8): address 58

address

already allocated!

Note:

If you select an address that has already been allo-

cated, the message on the right will be displayed.

Содержание TAK5-CH1-25



































































































































































































































Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды

Foerster TAK5-CH1-25, Инструкция по эксплуатации

Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды