Foerster TAK5-CH1-25 Скачать руководство пользователя страница 107

Страница: 107 / 226

Feeding

107

If the animal has no feed entitlement anymore, the box valve

closes after the bar electrode is free again and draining time has

lapsed.

If the bar electrode remains covered, the box valve closes after

hold time has lapsed.

If an animal breaks off feed intake, five minutes after feed prep-

aration the remaining quantity in the mixer jar will be released

thus being available for any other entitled animal. The consumed

quantity is booked for the animal. Alternatively, the feed can also

be drained immediately via the mixer draining valve, if available.

Feeding program

After the animals have been registered in a group (A, B, C or D),

they are fed according to the feeding plan of the corresponding

group.

The daily feed quantity is spread over several intervals according

to the interval feeding system (

Basic principle of interval

feeding

Minimum quantity

The minimum quantity is intended to prevent the animals from

consuming too small quantities. When a calf achieves the corre-

sponding minimum quantity, this quantity will be released.

Maximum quantity

In order to avoid excessive feed intake due to too high minimum

quantities, the quantities to be consumed are limited. If an animal

has consumed the maximum quantity, feed dispense will be bro-

ken off for two hours for this specific animal. The accumulated

quantities are still effective.

Содержание TAK5-CH1-25



































































































































































































































Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды

Foerster TAK5-CH1-25, Инструкция по эксплуатации

Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды