Foerster TAK5-CH1-25 Скачать руководство пользователя страница 105

Страница: 105 / 226

Feeding

105

Feeding

8.1

Functioning of the automatic feeder

8.1.1

Feed preparation

During feed preparation the liquid components are dispensed

first. As soon as the liquid in the mixer jar touches the bar elec-

trode, milk powder will be dispensed from the powder hopper

into the mixer jar. There, the portion is intensely mixed.

The warm water needed to prepare the portion is extracted from

the boiler. The warm milk is pumped through the stainless steel

coil of the heat exchanger into the mixer jar.

The circulation pump keeps the warm boiler water moving at

high speed thus effecting a rapid heat transfer to the liquid in the

stainless steel coil. The circulation pump is active when an ani-

mal is consuming a feed portion or when the calibration or a

cleaning process are being carried out. If no feed has been con-

sumed, the circulation pump will be actuated every 15 minutes

for 30 seconds.

8.1.2

Feed dispense

The feed can be dispensed at the stations either in the

parallel

or the

priority mode

. Whereas in the

parallel mode

several ani-

mals can be simultaneously fed at different stations, in the

prior-

ity mode

only one animal at a time can be fed.

Note

: Please consider the documentation of the periph-

eral devices, if required.

Содержание TAK5-CH1-25



































































































































































































































Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды

Foerster TAK5-CH1-25, Инструкция по эксплуатации

Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды