INr4-GYB
接收机 Receiver
Http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
产品型号：INr4-GYB
适配发射机：所有支持 AFHDS 3 的枪控发射机
适合机种：车、船等
PWM 通道：4
无线频率：2.4GHz ISM
无线协议：AFHDS 3
天线类型：单天线
输入电源：3.5 ～ 9V / DC
数据输出：PWM/PPM/i-BUS2/S.BUS/i-BUS
温度范围：-10℃ ~ +60℃
湿度范围：20%~95％
在线更新：是
外形尺寸：17*29*16.6mm
机身重量：6.5g
认证： CE, FCC ID:N4ZINR4GYB0
INr4-GYB 采用 AFHDS 3（第三代自动跳频数字系统），
外置单天线带回传功能，内置陀螺仪，设计小巧轻便，
易于安装，支持 4 个 Newport 功能接口（Newport
接口可自定义输入或输出的信号类型：i-BUS2/S.BUS/
i-BUS/PPM 等），支持所有 AFHDS 3 发射机。
The INr4-GYB receiver adopts Flysky's third-generation automatic frequency
hopping digital system (AFHDS 3).It uses a single-antenna bidirectional
transmission system, with built-in gyroscope and is uniquely designed to
install. It supports 4 Newport function interfaces (Newport interface can
be customized with the input or output signal type: i-BUS2/S.BUS/i-BUS/
PPM, etc.). It adapts all transmitters which support AFHDS 3 protocol.
产品介绍
Introduction
接收机概览
Receiver overview
对码
Binding
产品规格
Product specification
[1] CH1(NPD)
[2] CH2(NPC)
[3] CH3(NPB)
[4] CH4(NPA)
[5] 对码按键
[6] BVD/VCC（电池电压检测 / 供电接口）
[7] LED 灯
[8] 天线
[9] 信号脚
[10] +（电源正极）
[11] -（电源地）
[12] BVD 功能配件
[13] 接电池正极
[14] 接电池负极
[12]
[13]
[14]
[1] CH1(NPD)
[2] CH2(NPC)
[3] CH3(NPB)
[4] CH4(NPA)
[5] BIND button
[6] BVD/VCC(Battery voltage detection/
Power supply interface)
[7] LED
[8] Antenna
[9]S（Signal Pin）
[10] + (Power anode)
[11] - (Power cathode)
[12] BVD harness
[13] Connect to battery anode
[14] Connect to battery cathode
Product Model: INr4-GYB
Adaptive transmitter: All surface transmitters which support
AFHDS 3 protocol.
Model Type: Cars or Boats, ect.
PWM Channels: 4
RF: 2.4GHz ISM
2.4G Protocol: AFHDS 3
Antenna: Single Antenna
Input Power: 3.5 ～ 9V/ DC
Data Output: PWM/PPM/i-BUS2/S.BUS/i-BUS
Temperature Range: -10℃ ~ +60℃
Humidity Limit: 20%-95%
Online Update: Yes
Dimensions: 17*29*16.6mm
Weight: 6.5g
Certification: CE, FCC ID:N4ZINR4GYB0
[6]
[8]
[7]
[10] [11]
[9]
[4]
[5]
[3]
[2]
[1]
1. 使发射机进入对码状态 ;
2. 按住接收机对码按键同时上电后松开对码键（或者先给接收机上电后，长按对码键 3 秒），接收机指示灯快闪，表示进入对码状态；
3. 当接收机指示灯变为常亮时，对码成功 ;
•
当对码的发射机是单向模式进入对码状态时，接收机 LED 灯变为慢闪后将发射机退出对码状态，此时接收机 LED 灯常亮，表示
对码成功；
4. 检查发射机、接收机、模型是否正常工作。如需重新对码，请重复以上步骤。
1. Put the transmitter to enter bind mode;
2. Press and hold the
receiver BIND button [5] while powering on the receiver, release the BIND button after receiver is powered on or
powering on the receiver first, then press and hold the BIND button 3 seconds, the LED [7] of the receiver will flash rapidly
, indicating
the receiver is in bind mode;
3. The binding process is complete when the LED of the receiver stops flashing and is on continuously.
•
If a transmitter that has had its radio frequency (RF Standard) set to "AFHDS3 1 way" (please refer to your transmitter user
manual) enters bind mode, after the receiver LED becomes slow flashing, then put the transmitter to exit the binding state. At this
time, the receiver LED is solid on indicating the binding is successful.
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems
arise.
注：
BVD 电压检测范围： 0~70V
Note
: BVD voltage detection range: 0~70V
