background image

5

4.Instructions

   

After setting up, follow the instructions below to operate the system.

Follow the steps below to turn on the transmitter:
1.  Check to make sure that that battery is fully charged and installed correctly.
2.   Toggle the switch to the [ON] position. When active the R.LED will be lit.   
3.   Connect the receiver to power.  

•  For safety always power on the transmitter before the receiver. 

4.3 Binding

The transmitter and receiver have already been bound at the factory. 

1.    Turn  on  the  transmitter  while  holding  the  bind  button  to  enter  bind  mode.  G.LED  will  start 

flashing quickly. 

•   

Once in bind mode release the bind button.

2.  The receiver will enter bind mode atomically when powered on.
3.    Once  binding  is  successful  the  receiver’s  LED  will  flash  slowly  and  the  transmitter’s  LED 

will remain solid after being rebooted. 

Note: When binding, put the transmitter into bind mode first, then the receiver. 

4.1 Power On

However if the receiver needs to be replaced or additional receivers bound follow these steps: 

  

Note •  Operate with caution in order to avoid damage or injury.

  

Note

•  Make sure that the throttle is at its lowest position and the switches are set to their  up 

position.  

• 

applicable to the FS-MG4 transmitter and the FR-R4B receiver. Different receivers have 
different bind procedures. For more information visit the FLYSKY website for manuals and 
other related information. 

• 

Product information is updated regularly, please visit our website for more information.  

4.2 LED 

1.  R.LED: Red power indicator;
2.  G.LED: Green status indicator;
3.  Low battery alarm: When the battery is lower than 4.2v, the G.LED on the panel will flash slowly.

Содержание FS-MG4


















Отзывы: