6.
The operator or user is responsible for accidents or
hazards occurring to other people or their property.
7.
Read the user instructions carefully to make sure you
understand all the controls and what they do.
Electrical
1.
We recommend the use of a Residual Current Circuit De-
vice (R.C.D.) with a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be guaran-
teed and safe working practice must be followed at all times.
Check your R.C.D. every time you use it.
2.
Before use, examine cable for damage or ageing. If the
cable is found to be defective, take the product to an Au-
thorised Service Centre and have the cable replaced.
3.
Do not use the product if the electric cables are dam-
aged or worn
4.
Immediately disconnect from the mains electricity supply if
the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable. Re-
place it with a new one.
5.
Your extension cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of your product.
6. Keep cable away from product, always work away from
the power point mowing up and down, never in circles.
7.
Do not pull cable around sharp objects.
8.
Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9.
Switch off, remove plug from mains and examine elec-
tric supply cable for damage or ageing before winding
cable for storage. Do not repair a damaged cable, re-
place it with a new one. Use only Flymo replacement
cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Flymo Products are double insulated to EN60335.
Under no circumstance should an earth be connected
to any part of the product.
Preparation
1.
While using your product always wear substantial
footwear and long trousers.Do not operate the equip-
ment when barefoot or wearing open sandals.
2.
Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
3.
Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4.
Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1.
Use the product only in daylight or good artificial light.
2.
Avoid operating your product in wet grass, where feasible.
3.
On slopes, be extra careful of your footing and wear
non-slip footwear.
4.
Mow across the face of slopes, never up and down.
5.
Exercise extreme caution when changing direction on
slopes. Walk never run.
6.
Do not mow excessively steep slopes.
7.
Do not walk backwards when mowing, you could trip.
8.
Never cut grass by pulling the product towards you.
9.
Switch off before pushing the product over surfaces
other than grass.
10. Never operate the product with damaged guards or
without guards in place.
11. Switch on the motor according to instructions and with
feet well away from the blade(s).
12. Do not tilt product when the motor is running, except
when starting and stopping. In this case, do not tilt
more than absolutely necessary and lift only the part
which is away from the operator. Always ensure that
both hands are in the operating position before return-
ing the appliance to the ground.
13. Do not put hands or feetnear or under rotating parts.
14. Never pick up or carry a product when it is operating or
still connected to the mains supply.
15. Remove the plug from the mains :
-
before leaving the product unattended for any period;
-
before clearing a blockage;
-
before checking, cleaning or working on the appliance;
-
if you hit an object. Do not use your product until you
are sure that the entire product is in a safe operating
condition;
-
if the product starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
1.
Caution - Do not touch rotating blade.
2.
Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
3.
Check the grassbox frequently for wear or deterioration.
4.
Replace worn or damaged parts for safety.
5.
Only use the replacement blade, and blade bolt speci-
fied for this product.
6.
Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
7.
Store in a cool dry place and out of reach of children.
Do not store outdoors.
8.
Allow the product to cool for at least 30 minutes before storing.
CABLES - IMPORTANT
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used.
-
1.0 mm
2
: max length 40 m
-
1.5 mm
2
: max length 60 m
-
2.5 mm
2
: max length 100 m
Minimum rating :
1.00mm
2
size cable, 10 amps 250 volts AC.
•
YOUR PRODUCT IS SUPPLIED WITH CABLE WIRED
DIRECTLY INTO THE PRODUCT.
1. If the supply cord is damaged, it must be replaced by
your local Husqvarna UK Ltd. Approved Service Centre
or similarly qualified persons in order to avoid a hazard.
2. Flymo Extension Cables are available from your local
Husqvarna UK Ltd. Approved Service Centre.
3. Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd.
Approved Service Centre for further information on the
connectors and kits available.
4. Only use extension cables specifically designed for out-
door use and which conform to one of the following
specifications: Ordinary rubber (60245 IEC 53), Ordinary
PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57)
CONNECTORS - IMPORTANT
•
Flymo connectors are suitable for use with 2 core cable
only. Under no circumstances should these connectors
be used for earthed products.
•
All Flymo connectors and cables are of splashproof con-
struction. They are not waterproof and must not be left out-
side permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
•
If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.
1. No earth required. Flymo products are double insulated
to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - NEUTRAL BROWN - LIVE
The wire which is coloured BLUE must be connected to
the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be connected
to the Terminal which is marked with the letter 'L' or
coloured RED.
4. It is important that the outer sheath is clamped correctly
into the 3-pin plug.
5. If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Approved Service Centres which can
be found in your local Yellow Pages.
