Fluke VIBGUARD compact Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

Fluke VIBGUARD compact Скачать руководство пользователя страница 18

4.1 System module

VIB 7.900

Schnittstellen, Anzeige- und Bedienelemente

1

PE

: Protective earth terminal connected to PE terminal; used for contacting the system hou-

sing, contacting the Ethernet socket.

2

24V 1, PG 1

: Connection for the system module supply.

24V 2 / 24V 3

: Supply for the accessories.

3

SYSTEM, EVENT

: LEDs for system status and event recorder.

4

RESET

:System reset button.

5

RS232

: Serial interface for service.

6

Connection terminals for voltage signals/vibration sensors (

AI1 to AI6

) and for RPM sensor (

TP

)

incl. status LEDs.

7

Connection terminals for digital input signal (

DI

), system OK relay (

SYS

) and relay output (

NO

)

incl. status LEDs.

8

LAN

: Ethernet connection with status LEDs (

LINK, ACT

) for data traffic.

9

IP PRESET

: Button for standard IP configuration.

LED displays on the system module

Analog inputs / tachometer pulse input

LED status

AI1 ... AI6

Sensor fault

Off

Channel not configured

18

Edition: 10.2018

Installation and Operation

«
...
16
17
18
19
20
...
»

Содержание VIBGUARD compact



















































Отзывы:

Нет отзывов