Fluke RUSKA 7750i Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 106

Fluke RUSKA 7750i Скачать руководство пользователя страница 88

RUSKA 7750i

Users Manual

6-14

(9-pin to 9-pin, null modem cable minimum pinout 2-3, 3-2, 5-5).
1.

When appropriate, the latest version of the software for upgrading instruments can be

e-mailed from the factory, or downloaded from the website: www.gesensing.com.

The e-mail will have a zip file attached contains two files UPDATE7.EXE and

<version>.IMG. Unzip these files into a directory on the PC.

2.

Set the RUSKA 7750i to 9600 baud, 8 databits, no parity, 1 stopbit.

3.

Run the program Update7.

4.

Follow the prompts to select the communications port and the image file.

5.

When the upgrade is finished, Update7 running on the PC and the RUSKA 7750i

should both display Complete.

RUSKA 7750i Controller Software Upgrade

In addition to the main code, the RUSKA 7750i include code for the pressure controller.

The controller software version can be viewed by pressing the

MENU/TEST/REMOTE/SERIAL2 keys. The controller software version is displayed

next to ‘Ctrl’. This code can be upgraded through the RS-232 port on most units. Press

the MENU/TEST/CONTROL key and check for ‘Download Yes’.
(The digit in front of the R increases with revision levels and the last two digits will

increment upwards as the revision level increases, e.g. 0R99 is older code than 1R01

which is older than 1R08, etc.)
1.

Connect a PC to the RS-232 port on the RUSKA 7750i using a null modem cable.

2.

The zip file labeled RUSKA 7750iControl|XRXX contains files UPDATE7.EXE and

<version>.IMG. Unzip these files into a directory.

3.

Set the RUSKA 7750i to 9600 baud, 8 databits, no parity, 1 stopbit.

4.

Run the program Update7.

5.

Follow the prompts to select the communications port and the image file.

6.

Update 7 should display Complete.

Note

When updating the controller code, the RUSKA 7750i will display various
error messages. This is expected. The front display will freeze on the
RUSKA 7750i when the controller code is being downloaded. It will
operate properly once the download is complete. Finally, the main software
only reads the software versions on power-up. So, following the controller
code upgrade, pressing the MENU/TEST/REMOTE/SERIAL2 keys will only
show the new revision level of the controller code after power is cycled on
the RUSKA 7750i.

Replacement Parts

The following is a list of the common replacement parts used in the

RUSKA 7750i ADTS.

Table 6-2. RUSKA 7750i ADTS - Parts List

Description Part

Number

Valve Body

Valve Coil

Ps Test Valve

3961365

3915780

«
...
86
87
88
89
90
...
»

Содержание RUSKA 7750i











































































































Отзывы:

Нет отзывов