manualshive.com logo in svg

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Fluke PG9000 Series Скачать руководство пользователя страница 120

PG9602™ OPERATION AND MAINTENANCE MANUAL 

© 2011 Fluke Calibration 

Page 

110

 

and verify that the readings are correct. Note that a fluid head correction should be 
set if the external barometer is not at the PG9000 reference level.  This correction 
may cause the reading of the external barometer and the value of ambient 
pressure indicated by the PG9000 to not be identical (see Section 3.12.3.3). 

Note 

For communications with an external barometer on COM2 to be 
established properly, the inquiry string to send to the barometer 
must be defined following this section and the PG9000  COM2 
port and barometer COM port must have the same 
communications settings.  Press [SPECIAL] and select 
<5remote>, <2COM2>, <1settings> to set up PG9000  COM2 
communications settings.  When unable to establish 
communications between COM2 and the external barometer, 
consider using the PG9000  RS232 self test to verify COM2 
operation (see Section 3.12.5.3).    If both a barometer and a 
vacuum gauge are connected, the barometer must be an RPM3 
or RPM4 and must  always be the first device connected to the 
PG9000 Platform COM2. 

3.12.5.5  External Vacuum Gauge Communications (COM2) 

 

PURPOSE 

To configure  communications with an external vacuum gauge from which PG9000 
will read the value of reference vacuum under the bell jar used in the calculation of 
absolute pressure in absolute by vacuum measurement mode (see Section 3.10.4). 

Note 

The source of the value of vacuum pressure used by PG9000 in its 
internal calculations is determined by the Vac setting in the current 
SETUP file (see Section 3.11. Configuring communications with an 
external vacuum gauge does NOT set PG9000  to utilize the 
external vacuum gauge. 

 

PRINCIPLE 

PG9000  measures the  reference vacuum under the bell jar in its calculation of 
the pressure defined by the PG in absolute by vacuum measurement mode (see 
Section  7.2).  The source of the value is determined by the Vac setting in the 
current SETUP file (see Section 3.11).  The standard source  of this value  is 

COM2

, which allows an vacuum gauge  connected to PG9000’s COM2 RS232 

port to be read automatically to obtain the reference vacuum values that are 
used.  In order to communicate with the external vacuum gauge, PG9000’s 
COM2 must be properly set up.  This setup occurs by pressing 

[SPECIAL]

 and 

selecting 

<5remote>

, 

<2COM2>

, 

<3vac>

. 

Note 

If a Fluke Calibration (DH  Instruments)  RPM3 or RPM4  is being 
used on COM2 for external measurement of barometric pressure, 
the vacuum gauge may be connected to COM2 of the RPM.  In this 
case, COM2 of the RPM barometer must be configured with the 
same communication settings as the external vacuum gauge.  If 
both a barometer and a vacuum gauge are connected, the 
barometer must always be the first device connected to the 
PG9000 Platform COM2. 

 

Содержание PG9000 Series











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды