Fluke LinkRunner AT 1000 Скачать руководство пользователя страница 26

Страница: 26 / 36

LinkRunner AT 1000/2000 Network Auto-Tester

Users Manual



General Configuration:



Cable Length Unit, Meters



Auto Shutoff, Enabled



Set Language:



English

When you Select

Restore Factory Defaults

, you will be

prompted with a two popup. Select



, then press

The restore will be completed and the tester will turn off.

Firmware Update

Download the LinkRunner firmware update file from
the Fluke Networks website, or contact Fluke Networks
to get the update by other means. Save the file to your
hard disk.

Get the latest version of LinkRunner Manager from the
Fluke Networks website.

Start LinkRunner Manager on your PC.

Turn on the tester.

Select

Tools > Firmware Update > select



Update

Use the USB cable supplied with the tester to connect
the tester to the PC.

In LinkRunner Manager, select

LinkRunner

Update

Software

Click

Select

, find and select the update file (.zip

extension), then click

Select

Click

Update

When the transfer is completed, disconnect the USB
cable from the tester.

The screen on the tester goes blank while it installs the
update file. When the update is completed, restart the
tester.

Caution

Do not disconnect the LinkRunner from the PC or
remove the battery during the update.

Содержание LinkRunner AT 1000





































Результаты поиска

Содержание LinkRunner AT 1000

Отзывы:

Похожие инструкции для LinkRunner AT 1000

Бренды по названию

Популярные бренды

Fluke LinkRunner AT 1000, Руководство пользователя

Результаты поиска

Содержание LinkRunner AT 1000

Отзывы:

Похожие инструкции для LinkRunner AT 1000

Бренды по названию

Популярные бренды