Fluke LinkRunner AT 1000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

background image

LinkRunner AT 1000/2000 Network Auto-Tester

Users Manual

12

VLAN/MAC Configuration

Select

Tools > VLAN/MAC Configuration

.

ffy41.bmp

Figure 6. VLAN/MAC Configuration Screen

This screen allows you to enable and enter the VLAN IP and
its Priority level. By un-checking the VLAN check box, the
VLAN capability is disabled.

This screen also allows you to enable and enter a user
defined MAC address. By un-checking the Enable User
Defined MAC check box, the LR-AT reverts back to the
factory default MAC address.

AutoTest Configuration

Select

Tools > AutoTest Configuration

.

ffy42.bmp

Figure 7. AutoTest Configuration Screen

This screen allows you to enter up to ten key device
addresses (Targets) to test connectivity. You may enter an IP
address, URL, or DNS name. If no port is specified, AutoTest
will perform an ICMP Ping test to that address. If a port is
specified, AutoTest will perform a TCP Connectivity test
(SYN/ACK).

The Continuous Mode check box allows the test to run
continuously (checked) or one time (un-checked). When
you exit the AutoTest screen, the test is stopped.

«
...
18
19
20
21
22
...
»

Содержание LinkRunner AT 1000





































Отзывы:

Нет отзывов

Похожие инструкции для LinkRunner AT 1000

Бренд: ICS ELECTRONICS Страницы: 6

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: Oberheim Страницы: 40

Бренд: Baileigh Industrial Страницы: 40

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

ActiveFinder One

Бренд: LaserLiner Страницы: 92

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

LSP400 LED Series

Бренд: WE-EF Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды