Fluke CableAnalyzer DSX-602 Скачать руководство пользователя страница 41

Страница: 41 / 110

Chapter 2: Certify Twisted Pair Cabling

Settings for Twisted Pair Tests

Setting

Description

Store Plot Data

Off

The tester does not save plot data for frequency-

domain tests or for the HDTDR/HDTDX analyzers. You
can see the plots before you save the test and exit the
results screen. The saved results show frequency-domain
measurements in a table and do not include the HDTDR/
HDTDX plots.

The tester saves plot data for all frequency-

domain tests required by the selected test limit and for
the HDTDR/HDTDX analyzers.

HDTDR/HDTDX

Fail/Pass* only:

The tester shows HDTDR and HDTDX

analyzer results only for Autotests with

PASS*

FAIL*

FAIL

results.

All Autotests:

The tester shows HDTDR and HDTDX

analyzer results for all Autotests.
To get HDTDR/HDTDX analyzer results you can also tap

TOOLS

Diagnostics

For more information about the HDTDR and HDTDX
analyzers, see the Technical Reference Handbook.

Outlet
Configuration

The

Outlet Configuration

specifies which wire pairs are

tested and which wire numbers the wire map shows for the
pairs. See Figure 11.
To see the wire map for a configuration, tap

Outlet

Configuration

, tap the configuration name on the

OUTLET

CONFIG

screen, then tap

SAMPLE

To select a configuration, tap a name on the

OUTLET

CONFIG

screen, then tap

USE SELECTED

Note

The

OUTLET CONFIG

screen shows only the

configurations that are applicable to the
selected

Test Limit

To make a custom outlet configuration, tap

CUSTOM

the

OUTLET CONFIG

screen, then tap

MANAGE

, then tap

Create

Table 2. Settings for Twisted Pair Tests (continued)

Содержание CableAnalyzer DSX-602















































































































Результаты поиска

Содержание CableAnalyzer DSX-602

Отзывы:

Бренды по названию

Популярные бренды

Fluke CableAnalyzer DSX-602, Руководство пользователя

Результаты поиска

Содержание CableAnalyzer DSX-602

Отзывы:

Бренды по названию

Популярные бренды