Fluke CableAnalyzer DSX-5000 Скачать руководство пользователя страница 608

Страница: 608 / 700

Versiv Series Cabling Certification Product Family

Technical Reference Handbook

572

Under the

Cable Type

, tap

NVP

Attach a channel adapter to the tester.

Connect a known length of twisted pair cable to the tester.
The cable must be a minimum of 30 m (100 ft) long.

Tap

MEASURE

On the

NVP

screen, use

to change the NVP value

until the measured length is the length of the cable, then tap

SAVE

Reset the NVP to the Default Value

To reset the NVP to the default value defined by the selected
cable type, select the cable type again on the

TEST

SETUP

screen.

Make a Custom Outlet Configuration

Custom outlet configurations start with the T568A or T568B
configurations. You can enable or disable each pair, and give the
configuration a name.

To make a custom outlet configuration

On the home screen, tap the test setup panel, tap a copper
test, then tap

EDIT

On the

TEST SETUP

screen, tap

Outlet Configuration

Tap

CUSTOM

, then tap

MANAGE

, then tap the

Create

panel.

Select the

T568A

T568B

configuration then select the pairs

you want enabled.

Enter a name for the configuration, then tap

SAVE

. The tester

adds an asterisk (*) to the start and end of the custom
configuration name.

To use the configuration, tap it on the

OUTLET CONFIG

screen, then tap

USE SELECTED

Содержание CableAnalyzer DSX-5000





























































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CableAnalyzer DSX-5000

Отзывы:

Fluke CableAnalyzer DSX-5000, Техническое справочное руководство, Страница: 608 / 700

Результаты поиска

Содержание CableAnalyzer DSX-5000

Отзывы: