manualshive.com logo in svg

Fluke CableAnalyzer DSP-4100, Руководство пользователя

Поделиться
Скачать
Fluke CableAnalyzer DSP-4100 Скачать руководство пользователя страница 83

Autotest

Autotest Results for Twisted Pair Cabling

3

3-17

Table 3-4. Items on the ELFEXT Results Screen

Item

Description

Pairs

The pairs used in calculating the ELFEXT result. The pair not listed as the
Atten. Pair produced the FEXT used in the ELFEXT calculation

Atten

.

Pair

The pair that produced the attenuation value used in the ELFEXT calculation.

Result

The overall result for the ELFEXT test. A 

PASS

 result means that the

calculated ELFEXT is higher than the value specified for the selected test
standard. A 

FAIL

 result means that the calculated ELFEXT is lower than the

specified value.

ELFEXT 
(dB)

The worst margin and worst ELFEXT. The worst margin is the ELFEXT value
that is closest to falling below specifications, or the value that exceeds
specifications by the greatest amount. The worst ELFEXT is the lowest
ELFEXT value measured.

Frequency

The frequencies where the worst margin and worst ELFEXT values occurred.

Limit

The lowest ELFEXT values acceptable for the frequencies above.

Margin

The difference between the ELFEXT values and the limits. A positive number
means that the ELFEXT is higher than the limit. A negative number means that
the ELFEXT is lower than the limit.

Содержание CableAnalyzer DSP-4100

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды