manualshive.com logo in svg

Fluke 9009, Руководство пользователя

Поделиться
Скачать
Fluke 9009 Скачать руководство пользователя страница 16

9009

User’s Guide

12

The proportional band width is set at the factory. The proportional band width is easily adjusted from 
the front panel. Set the width to discrete values in degrees C or F

,

 which depends on the selected units. 

The proportional band adjustment is accessed within the secondary menu. Push 

SET

 and 

EXIT

 to 

enter the secondary menu and show the heater power. Then push 

SET

 to access the proportional 

band.
Push 

SET

 and 

EXIT

Access heater power in secondary menu

SEC

Flashes for secondary menu, then shows the heater power 

13.0 P

Heater power in percent

Push 

SET

 

Access proportional band

ProP

Flashes ProP and the current setting

4.1

Proportional band setting

To change the proportional band

,

 push 

UP

 or 

DOWN

.

10.0

New proportional band setting

To accept and store the new setting push 

SET

. Push 

EXIT

 to continue without storing the new value.

Controller Configuration

The controller has several configuration and operating options and calibration parameters which are 
programmable through the front panel. To access these, push 

SET

 from the secondary menu after the 

proportional band. The display shows Config and then PAr for the first of three sets of configuration 
parameters- operating parameters, serial interface parameters, and calibration parameters. To select 
the menus

,

 push 

UP

 and 

DOWN

 and then push 

SET

 

(see Figure 

2

).

Operating Parameters

The operating parameters menu is indicated by,

PAr 

Operating parameters menu

Push 

SET

 to enter the menu. The operating parameters menu contains the HL (High Limit) parameter 

which adjusts the upper set-point temperature. The factory default and maximum are set to 350   C. For 
safety, adjust the HL down to restrict the maximum temperature set-point.

HL

Flashes HL, then shows the current value

H=350

Current HL setting

Adjust the HL parameter with 

UP

 or 

DOWN

.

H=300

New HL setting

Push 

SET

 to accept the new temperature limit.

Содержание 9009































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды