manualshive.com logo in svg

Fluke 522A/6, Руководство оператора

Поделиться
Скачать
Fluke 522A/6 Скачать руководство пользователя страница 322

5522A 

Operators Manual 

10-8 

Oscilloscope Input Capacitance Measurement Specifications   

Scope input selected 

1 M

Ω

 

Measurement Range 

5 to 50 pF

 

Uncertainty 

±

(5 % of input + 0.5 pF)

 [1]

 

[1] 

Measurement made within 30 minutes of capacitance zero reference. Scope option must be selected for at least five minutes prior 
to any capacitance measurement, including the zero process. 

Overload Measurement Specifications 

 

Source Voltage 

Typical ‘On’ current 

indication 

Typical ‘Off’ current indication 

Maximum Time Limit DC or AC 

(1 kHz) 

5 to 9 V 

100 to 180 mA 

10 mA 

setable 1  to 60 s 

Oscilloscope Connections 

 

Using the cable supplied with the SC1100 Option, connect the SCOPE output on the 

Calibrator to one of the channel connectors on your oscilloscope (see Figure 10-1). 
To use the external trigger, connect the TRIG OUT output on the Calibrator to the 

external trigger connection on your oscilloscope. To use the external trigger and view its 

signal with the calibration signal, connect the TRIG OUT output to another channel. See 

your oscilloscope manual for details on connecting and viewing an external trigger. 

5522A CALIBRATOR

 

gjh036.eps 

Figure 10-1. Oscilloscope Connection: Channel and External Trigger 

How to Start the SC1100 Option 

 

Press 

a

 (LED lit) to select the SC1100 Option. The SCOPE menu, shown below, 

appears in the Control Display. You can press any of the first four softkeys to go directly 

to the VOLT, EDGE, LEVSINE, and MARKER calibration menus. Press the last softkey 

to go to the OTHER menu (also shown below), allowing access to WAVEGEN, VIDEO, 

PULSE, Impedance/Capacitance measurement (MEAS Z), and Overload (OVERLD) 

menus. Press 

P

 to return to the SCOPE menu from the OTHER menu. This manual 

describes each of these menus in detail. 

Содержание 522A/6











































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды