Fluke 522A/6 Скачать руководство пользователя

Страница: 273 / 426

SC600 Oscilloscope Calibration Option

How to Calibrat the Voltage Amplitude on an Oscilloscope

9-11

amplitude signals. You can also toggle the trigger off and on by pressing ??.

•

V/DIV MENU

Opens the voltage scaling menu, which lets you select the scale of the

signal in volts per division. This menu is described below in detail, under “The

V/DIV Menu.”

•

MODE

Indicates you are in Volt mode. Use the softkey to change modes and open

the corresponding menus for the other four oscilloscope calibration modes

The V/DIV Menu

The V/DIV menu, shown below, sets the number of volts denoted by each division on the

oscilloscope. This menu provides alternative methods for changing the output amplitude

that may be more convenient for certain oscilloscope applications. To access the V/DIV

menu, press V/DIV from the Volt menu.

gjh053.eps

Each item in the V/DIV menu is described below.

•

V/div

Changes the scale of the output display by changing the number of volts that

are represented by each division. The available settings, shown in the figure above,

are provided in 1-2-5 step increments. Press the softkey under

to increase the

volts per division. Press the softkey under

DOWN

to decrease the volts per division.

•

# DIV

Specifies the number of divisions that establish the peak-to-peak value of the

waveform. The value can be adjusted from one to eight divisions. The amount

denoted by each division is displayed in the V/div field. Press the softkey under UP

to increase the signal’s height, and press the softkey under DOWN to decrease it.

Shortcuts to Set the Voltage Amplitude

The

and

keys step the voltages through cardinal point values of an

oscilloscope in a 1-2-5 step sequence. For example, if the voltage is 40 mV, then pressing

increases the voltage to the nearest cardinal point, which is 50 mV. Pressing

decreases the voltage to the nearest cardinal point, which is 20 mV.

Amplitude Calibration Procedure for an Oscillosope

This example procedure describes how to use the Volt menu to calibrate the

oscilloscope’s amplitude gain. During calibration, you will need to set different voltages

and verify that the gain matches the graticule lines on the oscilloscope according to the

specifications for your particular oscilloscope. See your oscilloscope manual for the

recommended calibration settings and appropriate gain values.
Before you start this procedure, verify that you are running the oscilloscope option in

Volt mode. If you are, the Control Display shows the following menu.

Содержание 522A/6











































































































































































































































































































































































































































Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды

Fluke 522A/6, Руководство оператора

Результаты поиска

Содержание 522A/6

Отзывы:

Похожие инструкции для 522A/6

Бренды по названию

Популярные бренды