manualshive.com logo in svg

Fluke Calibration P5515, Руководство пользователя

Поделиться
Скачать
Fluke Calibration P5515 Скачать руководство пользователя страница 12

P5515, P5515-V, & P5515-EP 

Users Manual 

4 

To avoid cross-contamination from other fluids, and protect the 

system from particulates, we recommend the use of a Liquid 

Separator, (refer to section Ancillary Equipment). 

W

 Warning 

DO NOT use Teflon/PTFE tape on these connections, as this 
will prevent correct sealing. The Gauge Adapter sealing system 
is designed for hand-tight sealing up to 20,000 psi / 1,400 
bar-wrenches or similar tools are not required — over 
tightening can cause damage to threads or sealing faces. 

Before connection, ensure that there is an O-ring fitted to the 
test port. 

Check that the sealing face of the device to be fitted is clean 
and undamaged, as scratches or dents can form leak-paths. 

Note 

The thread on the test port, and the lower part of the gauge adapters is 

LEFT-HANDED

. 

The following procedure details the correct method for mounting devices using these 

adapters.

  

1.

 

Screw the appropriate gauge adapter fully on to the instrument to be tested. 

 

gkx02.bmp 

Figure 2. Screw on Gauge Adapter 

2.

 

Screw assembly down COUNTER-CLOCKWISE on to test port. 

Note 

Hand-tight is sufficient; ensure that the bottom face contacts the O-ring on 
the test port. 

Содержание P5515





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды