Fluke Biomedical ProSim 8 Series Скачать руководство пользователя страница 100

Страница: 100 / 112

ProSim 8

Users Manual

Dynamic Waveforms

Types (default pressures) ................................... Arterial (120/80)

Radial artery (120/80)
Left ventricle (120/00)
Right ventricle (25/00)
Pulmonary artery (25/10)
Pulmonary-artery wedge (10/2)
Right atrium (central venous or CVP) (15/10)

Pressure Variability ............................................. Systolic and diastolic pressures are independently variable in 1 mmHg

steps.

Swan-Ganz Sequence

........................................... Right atrium, right ventrical (RV), pulmonary artery (PA), pulmonary

artery wedge (PAW)

Cardiac Catheterization

Chambers ........................................................... Aortic, Pulmonary valve, and Mitral valve

Respiration Artifact

Arterial, radial artery, and left ventricle ............... 5 % to 10 % multiplication
Other ................................................................... 5 mmHg or 10 mmHg

BP Output

.............................................................. Circular DIN 5-Pin

Power-On Default

.................................................. 0 mmHg

Respiration

Rate

........................................................................ 0 BrPM (OFF), 10 BrPM to 150 BrPM in 1 BrPM steps

Waves

..................................................................... Normal or ventilated

Ratio (inspiration:expiration)

Normal ................................................................ 1:1, 1:2, 1:3, 1:4, 1:5
Ventilated ............................................................ 1:1

Impedance Variations (

)

................................. 0.00

to 1.00

in 0.05

steps and 1.00

to 5.00

in 0.25

steps

Delta Accuracy

......................................................

(5 % of s 0.1

)

Baseline

................................................................. 500

, 1000

(default), 1500

, 2000

, Leads I, II, III

Baseline Accuracy

................................................

5 %

Respiration Lead

................................................... LA or LL (default)

Apnea Selection

.................................................... 12 seconds, 22 seconds, or 32 seconds (one-time events), or

continuous (Apnea ON = respiration OFF)

Power-On Default

.................................................. 20 BrPM, delta 1.0

Temperature

.......................................................... 30.0

C to 42.0

C in 0.5

C steps

Accuracy

................................................................

0.4

Compatibility

......................................................... Yellow Springs, Inc. (YSI) Series 400 and 700

Output

.................................................................... Circular DIN 4-pin

Cardiac Output

Catheter Type

........................................................ Baxter Edwards, 93a-131-7f

Calibration Coefficient

.......................................... 0.542 (0

C injectate), 0.595 (24

C injectate)

Blood Temperature

............................................... 36

C (98.6

F) to 38

C (100.4

0.2

C in 1

C steps

Injectate Volume

................................................... 10 cc

Injectate Temperature

........................................... 0

C or 24

Cardiac Output

...................................................... 2.5 liters per minute, 5 liters per minute, 10 liters per minute

7.5 %

Faulty-Injectate Curve

.......................................... Waveform for simulation available

Left-to-Right-Shunt Curve

.................................... Waveform for simulation available

Calibrated Pulse

.................................................... 1.5

C for 1 second

Connector

.............................................................. Circular DIN 7 pin

Power-On Default

................................................. 5 liters per minute, 0

C injectate, 37

C blood temperature

Содержание ProSim 8 Series

















































































































Результаты поиска

Содержание ProSim 8 Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke Biomedical ProSim 8 Series, Руководство пользователя

Результаты поиска

Содержание ProSim 8 Series

Отзывы:

Бренды по названию

Популярные бренды