Fluidwell F010-P Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 52

Fluidwell F010-P Скачать руководство пользователя страница 29

Page 29

FW-F010-P-M_v0404_01_EN.docx

4.6.2

TERMINAL 4-5: POWER SUPPLY - TYPE PX (DEFAULT) AND PD (OPTION)

To power the F010-P an internal battery can be used (type PB) and / or an external DC power
supply of 8-30V DC (type PX) or 16-30V DC (type PD).
Connect the "

-

" to terminal 4 and the "

+

" to terminal 5.

When power is applied to these terminals, the optional internal battery will be disabled / enabled
automatically to extend the battery life time.

4.6.3

TERMINAL 6: POWER SUPPLY TYPE PD: 8.2V SENSOR SUPPLY

With this option, a limited power supply for the sensor is available, for example to power a Namur
sensor. It offers 8.2V DC (max. 5mA).

This terminal is only available if type PD has been ordered

4.6.4

TERMINAL 9-10: POWER SUPPLY BACKLIGHT - TYPE ZB (OPTION)

To power the backlight, a voltage in the range 20-30V DC has to be connected.
Maximum current 30mA. Connect the "

-

" to terminal 9 and the "

+

" to terminal 10.

Fig. 21: Terminal connections - Backlight (ZB).

«
...
27
28
29
30
31
...
»

Содержание F010-P





















































Отзывы:

Нет отзывов