manualshive.com logo in svg

Fluidwell F010-P, Руководство пользователя, Страница: 14 / 52

Поделиться
Скачать
Fluidwell F010-P Скачать руководство пользователя страница 14

Page 14

 

FW-F010-P-M_v0404_01_EN.docx 

3.3.3 

EXPLANATION OF SETUP-MENU 2 - DISPLAY 

SETUP

 

FUNCTIONS

 

AND

 

VARIABLES 

2 

DISPLAY 

2.1 

BARGRAPH 

The bargraph (piegraph) displayed at operator level is percentage-
wise related to the input signal: minimum signal is 0% and maximum 
signal is 100% (setup 18).  
With this function, the bargraph can be enabled / disabled. 
Following selections are available: 
 
 

 

OFF - ON 

 

The functions below will only affect the optional LED-backlight. 

2.2 

BACKLIGHT (optional) 

If a LED backlight has been supplied, it can be turned on or off. 

2.3 

BL. BRIGHTNESS 
(optional) 

The backlight brightness is adjustable. The following can be selected: 
1 

– 5 (where 1 is minimum and 5 is maximum brightness) 

 

3.3.4 

EXPLANATION OF SETUP-MENU 3 - POWER MANAGEMENT 

When used with the internal battery option, the user can expect reliable measurement over a long 
period of time. The F010-P has several smart power management functions to extend the battery life 
time significantly. Two of these functions are available. 
 

SETUP

 

FUNCTIONS

 

AND

 

VARIABLES 

3 

POWER MANAGEMENT 

3.1 

LCD NEW 

The calculation of the display-information influences the power 
consumption significantly. When the application does not require a 
fast display update, it is 

strongly advised

 to select a slow refresh 

rate. Please understand that NO information will be lost; every pulse 
will be counted and the output signal will be generated in the normal 
way.  
The following can be selected: 
Fast - 1 sec - 3 sec - 15 sec - off. 

Example battery life-time with a coil pick-up: 

•

 

1kHz pulse and FAST update: about 2 years. 

•

 

1kHz pulse and 1 sec update: about 5 years. 

 

After a button has been pressed by the operator - the display refresh 
rate will always switch to FAST for 30 seconds. When "OFF" is 
selected, the display will be switched off after 30 seconds and will be 
switched on as soon as a button has been pressed. 

3.2 

BATTERY MODE 

The F010-P has two modes: operational or shelf.  
After "shelf" has been selected, the F010-P can be stored for several 
years; it will not process the sensor signal; the display is switched off 
but all settings and totals are stored. In this mode, power consumption 
is extremely low.  
To wake up the F010-P again, press the SELECT/

 key twice. 

 

 

Содержание F010-P





















































Отзывы:

Нет отзывов