manualshive.com logo in svg

Flowserve Argus EK 71, Руководство по обслуживанию

Поделиться
Скачать
Flowserve Argus EK 71 Скачать руководство пользователя страница 10

Argus 

Maintenance 

10 

Maintenance 

Type EK/71 

 
 

 

EK71-02-001 

 

 

 

Danger! 

Do not disassemble the valve under pressure. Before disassembly operate valve so that possible 
pressure behind the ball may escape. 

Disassembly 

f

  Stem (22) should be in CLOSED position. 

f

  Remove snap ring (12) and stop disk (7). 

f

  Detach screws (8, 9) with bush (5). 

f

  Remove cover plate (6) with sealing ring (43), on DN 32-50 with bearing tape (34) and dowel pin, as 

well as thrust ring (11) with sealing ring (35). 

∗∗

 

f

  Unscrew flange connection (2) with sealing ring (33) and O-ring (37) from body (1) using a special 

ARGUS tool (eccentric). 

f

  Remove ball (21) and sealing rings (31). 

f

  Press stem (22) downwards and take it out of the body together with bushing (36) and disks (38). 

f

  The O-ring (32) and disk (39) are removed upwards. 

Exchanging the Stem Sealing 

Proceed as per Disassembly until 

(∗∗)

.  

f

  Then exchange disk (39) and O-ring (32). When using a PTFE seal instead of O-ring (32), item (39) 

can be left out. 

 

Depending on the requirements, a partial disassembly of the ball valve may be sufficient.  

f

  To reassemble, proceed in reverse order. 

  三千控制阀网 

www.cv3000.com

Содержание Argus EK 71
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды