Flintec FT-111 AN Скачать руководство пользователя страница 33

Страница: 33 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

146

Installation of SD Card

Some features of the FT-111 requires SD card which its slot is located on the rear of the instrument like Modbus RTU / TCP.
These SD cards should be ordered for your usage.

Inserting the SD card

1. Deenergize the instrument and wait 30 seconds.
2. Insert the SD card into the slot until it locks into place.

3. Energize the instrument. FT-111 read the SD card at power on to initiate its function.

Removing the SD card

1. Deenergize the instrument.
2. Gently press on the SD card to release the lock, then carefully pull the card out.

3. Insert the new SD card as described above, if need be.
4. Energize the instrument 30 seconds later power off.

Содержание FT-111 AN



















































































































































Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды

Flintec FT-111 AN, Техническое руководство

Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды