Flintec FT-111 AN Скачать руководство пользователя страница 113

Страница: 113 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

112

146

10.8 EtherNet/IP

EtherNet/IP interface of the weighing instrument can be done via hub switch or serial bus over two EtherNet/IP
port.

1. Serial bus connection of instruments. You may connect instruments serial to your EtherNet/IP bus via

two ports.

2. Star connection. If you connect the instrument to your PLC via hub switch, you can use P1 or P2 port

on the instrument. You may change the port, if there is any malfunction on port in usage.

The EtherNet/IP interface supports 10/100Mbit, full or half duplex operation.

EDS file

for two port EtherNet/IP

is available on internet www.flintec.com

There are 4 announcement LEDs on the instrument to indicate the interface status as seen below.

(A) Network Status LED

LED State

Description

Off

No IP address

Green

Online, one or more connections established (CIP Class 1 or 3)

Green, flashing

Online, no connections established

Red

Duplicate IP address, FATAL error

Red, flashing

One or more connections timed out (CIP Class 1 or 3)

(B) Module Status LED

LED State

Description

Off

No power

Green

Controlled by a scanner in run state

Green, flashing

Not configured, or scanner in idle state

Red

Major fault (EXCEPTION state, FATAL error etc.)

Red, flashing

Recoverable fault(s)

In the case of red LED warning, check cabling, configuration, IP address and device name. Power off the
instrument and reenergize the instrument 30 seconds later.

LINK/Activity LED

LED State

Description

Off

No link, no activity

Green

Link (100 Mbit/s) established

Green, flickering

Activity (100 Mbit/s)

Yellow

Link (10 Mbit/s) established

Yellow, flickering

Activity (10 Mbit/s)

(A) Network Status LED

(B) Module Status LED

Link/Activity LED (port 1)

Link/Activity LED (port 2)

P1 interface (port 1)

P2 interface (port 2)

Содержание FT-111 AN



















































































































































Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды

Flintec FT-111 AN, Техническое руководство

Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды