FlexRadio Systems FLEX-6500 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 14

FlexRadio Systems FLEX-6500 Скачать руководство пользователя страница 11

Page 11

© 2017 FlexRadio Systems, v1.0.0

Reinstall RF Isolation cover

Note: Before reinstalling the RF Isolation cover, you may want to boot the radio to ensure that the new
MicroSD card is installed properly. Be very careful when booting the radio with the chassis and RF
Isolation covers removed.

Reinstall the RF Isolation cover.  Make sure that the RF Isolation cover is inserted properly in the RF shield
housing’s retaining tabs.  It is best to insert the cover on the side of the housing underneath the side of
the chassis first and then gently press down on the side facing away from the chassis.  Once installed it
should like the image below.

Once the RF Shield cover is installed, put two (2) new Warranty seal stickers on the RF Isolation shield in
the same place where the previous stickers were located. Be careful not to place any of the stickers on
the PCB board. The warranty seal sticker should only be on the silver RF Isolation housing and cover as
shown below.

«
...
9
10
11
12
13
...
»

Содержание FLEX-6500















Отзывы:

Нет отзывов