Flexiheat FHATX25 Скачать руководство пользователя страница 28

Страница: 28 / 32

RESET

AIR ERROR

>> RESET

The display shows a lack of air.

This error can appear if the tubes of pressure switch are

disconnected or obstructed or if the connection of air

combustion or fumes is obstructed. The error can also appear

if the exhaust fan or differential pressure sensor is defective.

To reset the error, press RESET

EXHAUST FAN ERR.

>> RESET

The display shows that the extractor does not work or is

disconnected.

Check the connection of the cable or check the good rotation

when the exhaust fan starts. If the exhaust fan does not rotate,

replace it.

To reset the error, press RESET

BRUNER ERROR

>> RESET

The display shows a default on the burner control device which

is located on the rear side of the control board plate.

The error can be linked to different problems.

CONDENSATE

ERROR

The display does not concern ATX range.

If this message is displayed on ATX model, check the

connector shunt of condensate level sensor, because this

model does not have float.

To reset the error, press RESET

SYSTEM

ERROR

The display shows a system default on the control board.

Replace and configure the new control board.

RESET

Содержание FHATX25

































Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды

Flexiheat FHATX25, Техническая документация инструкция

Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды