Flexiheat FHATX25 Скачать руководство пользователя страница 27

Страница: 27 / 32

7– TROUBLESHOUTING

WARNING : The power supply and gas supply must be cut before any intervention on the heater.

7.1 List of defect and solutions to problems

OVERHEATING

ERROR

The display shows that the safety thermostat with manual reset

is in default. Press the button of the thermostat.

The error can come from a power failure whereas the heater

was operating or because of a fan short-circuit. The default can

also come from a faulty components: fan condenser,

thermostat with manual reset, control board.

SENSOR P AIR

ERROR

The display shows that the differential pressure sensor is

disconnected or defective.

Check the connection or replace the pressure sensor.

AIR SENSOR

ERROR

The display shows that the blowing air temperature sensor is

disconnected or defective.

Check the connection or replace the air temperature sensor.

FUMES SENSOR

ERROR

The display shows that the fumes sensor is disconnected or

defective.

Check the connection or replace the fumes sensor located

under the exhaust fan.

PH/N INVERSION

ERROR

The display show a polarity reversal.

It is necessary to cut-off the power supply of the heater and

reverse the phase and neutral of the main power supply of

the heater. When the operation is complete, the message on

the display will disappear.

RESET

Содержание FHATX25

































Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды

Flexiheat FHATX25, Техническая документация инструкция

Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды