Flexiheat FHATX25 Скачать руководство пользователя страница 24

Страница: 24 / 32

6.3 Control board use

The gas heaters are equipped with a control board allowing to control the state of the units and configure

them.

MAXI POWER

2400 RPM PS OK

PREVENTILATION

2200 RPM PA X

The display shows that the burner is on pre-ventilation.

The second line indicates the speed of the extractor/exhaust fan

and PA the state of the air pressure switch.

PS must displays « X » when the extractor is OFF and « OK »

the pressure switch detects airflow.

When the burner is light up, the display shows if the burner is

working on Maxi power or Mini power. It shows also the speed of

the exhaust fan and the state or air pressure switch.

>> MAXI POWER 90

2400 RPM 110 PS

The display shows 5 information allowing the diagnostic :

1 - Burner asking for P. MAXI = >> or P. MINI = <<

2 - Burner state = MAXI POWER or MINI POWER

3 - The value in % of exhaust fan PWM = 90 (example)

4 - the speed of exhaust fan in RPM = 2400 (example)

5 - The air depression of exhaust fan in PA (110)

AXIAL FAN

OFF

The display shows the axial fan state (OFF or ON). The fan

operation is operated in two simultaneous ways:
-

According to a starting blowing temperature setup in factory at

45 °C
-

According a temporization when burner starts whatever the

blowing temperature.

When burner stops, only the temperature can maintain or restart

the fan if its value is higher that set point temperature (for setup,

refer to the chapter « control board setup »)

To change the display, press ▲

BLOWING

TEMPERATURE xx C

The display shows the average blowing temperature.

To change the display, press ▲

RESET

Содержание FHATX25

































Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды

Flexiheat FHATX25, Техническая документация инструкция

Результаты поиска

Содержание FHATX25

Отзывы:

Похожие инструкции для FHATX25

Бренды по названию

Популярные бренды