background image

5

Flexel

 Installation Manual

Cable Kit Instructions

4) Laying the cable. 

 
A hole is provided at the side of the box to feed out the cable.  Do not take the cable off the 
drum before laying as it will twist and  make the  installation difficult.. 
 

Connection is only required at one 
end. The first 3metres is black  
cable that can be cut as required. 
The orange cable is the heated 
part that must never be cut or 
shortened.  
 
As shown loop the cables to the 
required marked spacings and 
secure to the floor as you go 
using the fixing tape supplied. 
Towards completion it may be 
necessary to slightly readjust the 
cable spacings to the available 
area. This will not be a problem 
as long as the cables remain at 
least 50mm apart and do not 
cross or touch each other.  

 

Never bury or try to hide the 
cable. If necessary, start again.  
 

If you have ordered the wrong size of kit contact your supplier. 
 

Now and referring to the tables on page 1 test the cable circuit for continuity 
(resistance) using an ohmeter. Avoid traffic over the laid  area until floor tiling is 
complete. 
 

5). Install the Thermostat and Floor Probe. 

 
Follow the instructions provided with the thermostat and the floor probe.  For the floor probe 
you will need to cut a channel for the protective spiral hose.  (This may have been done at an 
earlier stage as suggested).  Fix the hose into position and shorten to the required length.  
Feed the floor probe into the hose and block off the end.  The floor probe is then attached to 
the thermostat. 
 
The thermostat should be installed in the room that is to be heated.  F or bathrooms the 
thermostat must be placed outside the bathroom  but as close to the installation as possible.  
 
If necessary the heating cable cold tail and thermostat can be extended by up to 50 metres 
using cable supplied by Flexel International Limited. 

Figure 4. 

Содержание Ecofloor










Отзывы: