manualshive.com logo in svg

FLENDER K.A Series, Руководство по эксплуатации

Поделиться
Скачать
FLENDER K.A Series Скачать руководство пользователя страница 84

6.1.2

Gear unit with backstop

Take the following measures before commissioning the gear unit with backstop:
● Fill the backstop with oil (Page 95).
● Check that the backstop can be easily rotated in the free-wheeling direction without having 

to exert excessive force. When doing his, observe the direction of rotation arrows at the gear 

unit.

● Before connecting the motor, identify the phase sequence of the three-phase mains.

Connect the motor corresponding to the defined direction of rotation.

NOTICE
The backstop and the gear unit can be damaged
If you operate the gear unit adversely to the blocking direction of the backstop, the backstop 

and the gear unit can be damaged.
Do not operate the gear unit adversely to the blocking direction of the backstop. Observe the 

information on the plate attached to the gear unit.

6.1.3

Gear unit with auxiliary drive

Implement the following measures before commissioning the gear unit with auxiliary drive:
● Please observe the information provided in the operating instructions for the auxiliary drive.
● Fill the overrunning clutch with oil via the intermediate flange. Use the same oil type and 

viscosity as for the gear unit itself.

● If required, release the brake on the auxiliary motor.
● Check that the overrunning clutch can be easily rotated in the free-wheeling direction 

without having to exert excessive force. 

To do this, rotate the motor shaft of the auxiliary drive in the opposite direction to the 

direction of rotation arrow to the gear unit.

● Before connecting the auxiliary motor, identify the phase sequence of the three-phase 

mains.

Connect the auxiliary motor corresponding to the defined direction of rotation.

● Electrically interlock the main motor and the auxiliary motor so that only one of the two 

motors can be switched on.

● For a maintenance drive: Check the shutdown function of the speed monitoring.

Further information

You can find additional information on the auxiliary drive in the description (Page 41) and in the 

auxiliary drive operating instructions, provided in the complete gear unit documentation.

Commissioning
6.1 Measures to be taken prior to commissioning

REDUREX Gear unit  5200en

84

Operating Instructions 03/2019

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды