FLENDER K.A Series Скачать руководство пользователя

Страница: 63 / 128

Further information

You will find further information on the position of the torque arm in the dimension drawing,

which is part of the complete documentation of the gear unit.

5.4

Shaft-mounted gear unit with hollow shaft and parallel keyway

The shaft end of the driven machine shaft (material C60+N or higher strength) must have a

parallel key as defined by DIN 6885, Part 1, form A. Furthermore, it should have a hole centred

in its end face as defined by DIN 332, form DS (with thread). The connection dimensions for the

driven machine shaft can be found in the dimension drawing in the complete documentation.

View

The following diagram shows a gear unit with hollow shaft and parallel keyway:

①

End plate

④

Machine shaft

②

Hollow shaft

⑤

Bolts

③

Parallel key

Figure 5-6

Gear unit with a hollow shaft and parallel keyway

Mounting

5.4 Shaft-mounted gear unit with hollow shaft and parallel keyway

REDUREX Gear unit 5200en

Operating Instructions 03/2019

Содержание K.A Series

































































































































Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды

FLENDER K.A Series, Руководство по эксплуатации

Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды