manualshive.com logo in svg

FLENDER K.A Series, Руководство по эксплуатации

Поделиться
Скачать
FLENDER K.A Series Скачать руководство пользователя страница 45

Application planning

4

4.1

Scope of delivery

The scope of delivery is listed in the shipping documents. Immediately upon receiving the 

gearbox, check that everything has been delivered. Report any damaged and/or missing parts 

to Customer Services (Page 105) immediately.

WARNING

Serious injury through defective product
Serious injury may occur.
If the gearbox exhibits any visible damage, you should not put it into operation.

4.2

Transport

General information

The gear unit is delivered fully assembled. Additional items such as shrink disks, couplings, oil 

coolers, pipework and valves may be delivered separately packaged, as necessary.
When transporting the gear unit, observe the following instructions to avoid damaging the gear 

unit:
● Always use suitable equipment to transport the gear unit.
● Transport the gear unit without oil filling and leave it in the transport packaging.
● Do not use incorrect attachment points.

The threads in the end faces of the shaft ends may not be used for attaching lifting 

equipment.

● Do not use the pipework to move the gear unit.
● Ensure that the lifting equipment is adequately designed to accommodate the weight of the 

gear unit.

REDUREX Gear unit  5200en

Operating Instructions 03/2019

45

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды