FLENDER K.A Series страница 42 Скачать руководство пользователя

Страница: 42 / 128

The basic configuration of the gear unit with main and auxiliary drive is shown in the following

diagram.

①

Main gear unit

⑤

Main motor

②

Output shaft of the main gear unit

⑥

Auxiliary motor

③

Backstop

⑦

Auxiliary gear unit

④

Coupling

⑧

Overrunning clutch

Figure 3-14

Gear unit with main and auxiliary drive

Depending on the particular application, two auxiliary drives with two different ratings are

available for each gear unit size.

Further information

You can find further information, a detailed illustration of the gear unit and the position of the

auxiliary drive in the dimension drawing in the complete gear unit documentation.

3.16.1

Overrunning clutch

If, in addition to the main drive, you couple an auxiliary drive to the gear unit, then this coupling

is realised using an overrunning clutch.
When the auxiliary drive is used to drive the gear unit, the overrunning clutch allows torque to

be transferred in one direction of rotation, while "free-wheeling operation" applies when driven

by the main drive.
The output shaft of the main drive rotates in the same direction of rotation, irrespective of

whether the main drive is used or the auxiliary drive.

Principle of operation

The overrunning clutch as centrifugally-operated sprags. When the main gear unit rotates with

the specified direction of rotation, the inner ring with the sprags rotates, while the outer ring

remains stationary. Above a certain speed the sprags disengage, and the overrunning clutch

operates without any wear.
When the auxiliary unit drive motor is used as drive via the outer ring, then the overrunning

clutch is also driven; this means that the main gear unit is slowly rotated in the selected direction

Description
3.16 Auxiliary drive

REDUREX Gear unit 5200en

Operating Instructions 03/2019

Содержание K.A Series

































































































































Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды

FLENDER K.A Series, Руководство по эксплуатации

Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды