background image

Thank

 

you

 

for

 

your

 

purchase!

Customer

 

Service

 

Email:

 

[email protected]

 

|

 

Phone:

 

866-552-2810

ZG-021-WH-GG

 

/

 

ZG-021-GY-GG

ASSEMBLY INSTRUCTIONS

Before You Begin:

Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the

components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching

during assembly.

Caution:

Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may

result.

Warning:

CHOKING HAZARD

- Small Parts. Adult Assembly Required.

DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE

Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where

included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The

tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.

To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall

Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.

TV Stand

Содержание ZG-021-GY-GG




















Отзывы: