FlameStop VESDA-E VEP-A00-1P Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 112

background image

VESDA-E VEP-A00-P Product Guide

6

www.xtralis.com

2.3

Front Panel

The VEP-A00 detector provides the following information and control capability:

l

Status LEDs:

Alert, Action, Fire 1, Fire 2, Disabled, Fault and Power.

l

Controls:

Reset and Disable button.

2.3.1

Status LEDS

The VESDA-E VEP-A00 detector features a range of LED Indicators which illuminate when their respective
activation conditions are met.

LED

Symbol

Description

Fire 2

The Fire 2 LED is lit when the Fire 2 Alarm threshold is
reached.

Fire 1

The Fire 1 LED is lit when the Fire 1 Alarm threshold is
reached.

Action

The Action LED is lit when the Action threshold is reached.

Alert

The Alert LED is lit when the Alert threshold is reached.

Disabled

The DISABLED LED is lit continuously when the detector is
disabled and flashes once every two seconds when the
detector is in Standby mode.

Fault

The FAULT LED is lit when a fault condition is detected.

Refer to Chapter 8 for information on troubleshooting.

Power

The POWER LED illuminates when the detector is powered
up.

Table 2-1: LED Indicators

Notes:

l

The LEDs are tested during the power up cycle. To manually test the LEDs, run the Lamp Test using
Xtralis VSC.

2.3.2

RESET / DISABLE Button

Figure 2-2: Reset / Disable Button

Resetting the detector unlatches all latched alarms and faults, returns relays to their normal state and clears
the active event list in Xtralis VSC.

l

To reset the detector, press this button once.

Disabling the detector disables signaling of alarms and faults via the relays. The aspirator remains active.

Disabled mode is signaled on relay #1 by default. Other relays may also be configured to signal disabled
mode. Refer to sections 4.3.6 and 5.5.10 for further information. For example, disabled mode may be also
signaled as an additional condition on the Fault Relay (Relay #3).

l

To disable the detector, press and hold the button for approximately 4 seconds, until the DISABLED
LED illuminates continuously.

l

To re-enable the unit, press and hold the button for approximately 4 seconds, until the DISABLED
LED deactivates continuously.

l

While the detector is disabled, any faults may be cleared by pressing this button once.

«
...
10
11
12
13
14
...
»

Содержание VESDA-E VEP-A00-1P

















































































































Отзывы:

Нет отзывов

Похожие инструкции для VESDA-E VEP-A00-1P

RADIO CONTROLLED PROJECTION ALARM CLOCK

Бренд: La Crosse Technology Страницы: 25

Бренд: SOUNDMASTER Страницы: 74

Бренд: Barbecook Страницы: 40

Бренд: Johnson Controls Страницы: 6

Бренд: Siemens Страницы: 5

Бренд: Steelmate Страницы: 14

Бренд: Audiovox Страницы: 38

Бренд: Trevi Страницы: 8

SmartThings ADT Smoke Alarm

Бренд: Samsung Страницы: 34

Бренд: Sammut Страницы: 8

Бренд: SOUNDMASTER Страницы: 61

Бренд: INSAFE Страницы: 2

Бренд: bolid Страницы: 4

Бренд: AUTHOR Alarm Страницы: 12

Бренд: CrimeStopper Страницы: 16

Бренд: CrimeStopper Страницы: 15

Бренд: Ginnys Страницы: 20

Бренд: SPAL Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды