Page 1 of 2
INSTRUCTIONS FOR USE
Lazio
GENERAL INSTRUCTIONS
Remove the fireplace suite from the packing, checking that neither the heater nor the power cable has been damaged during transport. Do not operate the heater if
damaged. The accessories are found in a box that is packed at the side of the fireplace. Your fireplace suite is guaranteed for one year from the date of purchase. In
the unlikely event of a breakdown you have access to our customer services team, simply call
01543 251122
during office hours, 9am – 5pm or e-mail on
INSTALLATION OF THE FIREPLACE
The fire must be positioned so that the plug socket is accessible once the fire has been installed.
IMPORTANT: Access must be allowed for, so that the fire can be serviced. This involves the fireplace being moved forward in order to access the rear and top.
The mains cable must therefore be long enough to allow this. If the removal of the plug is absolutely necessary for installation, cut off in an area within 100mm
only of the plug itself. Do not cut the cable fireside of the connector block or seal fireplace to the wall using silicon o r adhesives; doing so will affect your
warranty. Please also note the warnings at the back of these instructions. Where the inset fire is being used in front of an existing chimney, it is important that
the chimney is blocked off to prevent airflow problems with the fire. Where a chimney is not blocked off sufficiently it may cause the heater to cut out and the
flame effect to stop or work poorly.
Electrical connections
Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA approved. If the fuse cover is lost the plug must
not be used until a replacement cover, of the same colour, is obtained an electrical retailer.
The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed. Under no
circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a hazard.
WARNING THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code.
Green and yellow:
EARTH
Blue:
NEUTRAL
Red:
LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: -
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or coloured green or
coloured green and yellow, or marked with the earth symbol
The wire, which is coloured blue, must be connected to the terminal in the plug, which is marked with the letter N, or coloured black.
The wire, which is coloured brown, must be connected to the terminal in the plug, which is marked with the letter L, or coloured red.
If the mains cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.
Fuel effect (pebbles)
Once the fire has been installed in the correct position unpack the fuel effect from the accessory box. Add the desired amou nt of pebbles by simply placing
them on the white tray around the curved screen.
OPERATING THE FIRE
Controls
This fire may only be operated by the remote control. There is standby
on/off
reset
switch topside of the fire opening under the heater compartment. This
is marked with
I/O
and will need to be switched to
I (standby)
to operate the remote.
The standby on/off reset switch is there for your safety and piece of mind. In the O position (off) you will be unable to operate the fire from the r emote
handset. We recommend always turning the fire off from here after use and storing the remote in safe place out of the reach of children. If for any
reason the remote becomes lost or damaged while the fire is on, switching to off (position O), waiting 30 seconds and switchi ng back on (position I) will
reset the fire back to its standby state. For details on replacing your remote see supplier or call Flamerite customer services direct.
1) To turn the fire on, simply press and release the
button on the remote keypad.
2) To set the light to your desired brightness, press then release the button marked
. You will notice the flame effect brightness will continuously
phase from high to low. At the desired point press then release the
button to stop the phasing.
3) For heating the fire must be switched on. To give 1KW of heat, press then release the button marked
O/I.
To increase the temperature to 2KW
press then release button marked
I/II
. You may change from 1 to 2kw or 2 to 1kw by pressing
I/II
at anytime. To turn the heater off, press
then release the button marked
O/I.
The heater will always start with 1kw and not 2kw.
4) To turn the fire off press then release the button marked
.
