background image

 

 

Note:   

There  may  be  some  arcing  or  snapping  sounds 

from the collecting cells. This  is normal  when the unit is 
new.  In  about  2  weeks,  as  the  sharp  edges  of  the  cells 
become smoother, the arcing will disappear. 

 

OPERATION 

The Air Cleaner will run as long as there is adequate 

airflow  through  the  ducts.  The  Air  Cleaner  will  not  run  if 
the  system  fan  is  off.  For  proper  operation,  follow  these 
simple steps: 
1.  Run heating/cooling system fan continuously, and on 

low speed if available. 

2.  Remove  furniture  or  carpets  which  block  return  air 

grilles  throughout  your  house,  so  that  air  moves 
freely to the furnace/ air conditioner. 

3.  Check for proper operation of the system fan. 

 

WHITE DUST 

After  installation  of  the  Air  Cleaner,  you  may  notice 

some  white  dust  on  tabletops  and  shelves.  Most  large 
particles  such  as  lint,  are  too  heavy  to  remain  airborne 
and tend to settle quickly, never reaching the air cleaner. 

This  white  visible  dust  is  normally  referred  to  as 

clean dust.” As the Air Cleaner is removing the dark and 

staining particles from the air, the lint will also be cleaner. 

Lint  dust  is  most  noticeable  on  dark  furnishings;  in 

homes containing new carpeting; and where there is a lot 
of household traffic from occupants and pets. To reduce 
lint  dust,  use  continuous  fan  operation  and  keep  return 
vents unrestricted to create an efficient airflow. 

Note:  

The Air Cleaner does NOT produce more lint or 

dust.

 

MAINTENANCE 

It is important to follow a scheduled maintenance for 
maximum performance of the Air Cleaner. 

Cell And Prefilter Cleaning 

The collecting cells and prefilters must be cleaned on 

a regular basis for the Air Cleaner to function at its peak 
of    efficiency.  The  frequency  of  cleaning  will  vary  from 
one  house  to  another.  On  average,  the  cells  should  be 
cleaned every 3 months. 
1.  Remove access door, collecting cells and prefilters. 
2.  Place cells in a laundry tub. Rinse with hot water and 

spray  completely  with  DAX  Detergent  (or  a  non-
chlorine,  non-corrosive,  non-abrasive  liquid 
household  detergent.  Allow  detergent  to  run  down 
both sides of plates and ionizing wires. Let stand for 
5  minutes  or  fill  up  laundry  tub  with  water  and  DAX 
Detergent, and dunk cells up and down until water is 
dirty. 

3.  Rinse  cells  well  with  hot  water  (maximum  120°F/ 

49°

C). 

4.  To  remove  contaminate  from  the  ionizing  wires  use 

an  old  toothbrush.  Slide  the  brush  bristles  over  the 
wire and gently drag the brush up and down the wire 
once.  Be  very  careful  when  cleaning  the  wires  as 
they become very brittle with age. 

5.  If dirt remains on the cell plates, let the cells soak in a 

solution of DAX Detergent and water for 30 minutes. 

6.  Tilt cells on 45° angle on their short side, with arrows 

pointing  sideways.  Allow  to  dry  completely, 
approximately 12-24 hours. A hair dryer may be used 
to speed up drying time. 

7.  To  wash  prefilters,  spray  with  DAX  Detergent,  rinse 

and  let  dry.  Do  not  wash  in  the  same  water  as 
collecting cells. 

8. 

Do not place the cells in the air cleaner if they are 
wet.

 

9.  Place  cells  and  prefilters  back  into  cabinet.  Close 

door  and  turn  power  switch  ON.  If  the  performance 
light  does  not  come  on  or  arcing  occurs,  turn  Air 
Cleaner  OFF  and  allow  air  from  system  fan  to  dry 
cells completely. 

Activated Carbon Filter Replacement 

Carbon filters help remove odors from the air. Carbon 

filters should be replaced every 3 - 6 months. Filters are 
NOT washable. Replacements are available through your 
 

CAUTION  

Make  sure  to  turn  Air  Cleaner  and  system  fan 

OFF 

before  performing  any  maintenance  or  removing  any 
components.  

CAUTION  

Damage  to  cells  may  occur  if  improperly  handled  or 
washed. Do  not  wash cells in a dishwasher. Never  use 
any object to clean between the cell plates, as this may 
cause  damage  to  plates  or  ionizing  wires.  Never  place 
cell in oven to dry. The edges of the cell may be sharp - 
handle with care.  

 

Replacement Carbon Filters: 
SASD10-2, SASD11-2       Set of 3       Part #1156-3 
SASD12-2, SASD18-2       Set of 3       Part #1856-3 

Fig. 6 

 DAX Detergent and Carbon Filters are 

available from your installer or dealer. 

DAX 

 

32 oz Spray Bottle 

Part #FS9900 

Содержание SASD10-2

















Отзывы: