manualshive.com logo in svg

Fisher A41, Инструкция по эксплуатации, Страница: 1 / 36

Поделиться
Скачать
Fisher A41 Скачать руководство пользователя страница 1

Fisher

r

A41 High Performance Butterfly Valve

Contents

Introduction

1

...............................................................

Scope of Manual

1

.................................................

Description

1

.........................................................

Specifications

2

....................................................

Educational Services

2

...........................................

Installation

5

................................................................

Valve Orientation

6

...............................................

Maintenance

9

.............................................................

Packing Maintenance

12

........................................

Seal Ring Maintenance for NPS 3 through 12

13

.....

Seal Ring Maintenance for NPS 2

19

.......................

Disc, Drive Shaft and Bearing Maintenance for

NPS 3 through 12

20

.........................................

Disc, Drive Shaft and Bearing Maintenance for

NPS 2

24

.............................................................

Actuator Mounting

26

...........................................

Parts Ordering

27

.........................................................

Retrofit Kits for ENVIRO-SEAL

t

Packing

27

............

Repair Kits for ENVIRO-SEAL Packing

28

..................

Parts List

28

...............................................................

Figure 1. Fisher A41 Valve

W9269

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for Fisher A41 high performance

butterfly valves (figure 1). Refer to separate instruction manuals for information covering the power on-off actuator

and accessories.

Do not install, operate, or maintain A41 valves without being fully trained and qualified in valve, actuator, and

accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you

have any questions about these instructions, contact your Emerson Process Management sales office before

proceeding.

Description

The A41 high performance butterfly valves have eccentrically mounted discs to reduce wear and reduce torque

requirements. The valve includes filled-PTFE or graphite packing rings that electrically bond the shaft to the valve

body. This valve has a Double D drive shaft end, and soft or metal seal rings for use in a wide variety of applications.

Instruction Manual

A41 Valve

www.fishvalve.nt-rt.ru

 

По вопросам продаж и поддержки обращайтесь:  

Волгоград (844)278-03-48

,

 Воронеж (473)204-51-73

,

 Екатеринбург (343)384-55-89

,

 Казань(843)206-01-48

,

 Краснодар(861)203-40-90

,

 Красноярск(391)204-63-61

,

Москва(495)268-04-70

,

 Нижний Новгород(831)429-08-12

,

 Самара(846)206-03-16

,

 Санкт-Петербург(812)309-46-40

,

 Саратов(845)249-38-78

, 

Единый адрес: 

fhv

@nt-rt.ru 

Содержание A41





































Отзывы:

Нет отзывов