manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 40

40

Installing wine display kit
Handle assembly
Retainer blocks are pre-assembled at the bottom of both ends of the handle.

Cradle assembly

A retainer block is pre-assembled at the bottom of each cradle.

WINE DISPLAY

Align handle to the front end of 
display rack.

2

Insert retainer block at desired 
location between slats of display 
rack. Do not tighten.

4

Place ‘cradle guide’ on the slats 
behind the handle.. 
Align cradle on spacer based on 
size and type of wine bottle.

5

Rotate the retainer block to lock 
position, and tighten screw.
Remove cradle guide from the rack 
after use.

6

Loosen the screws until the retainer 
blocks can be inserted between slats 
of display rack. 

1

Rotate retainer block to lock 
position and tighten screw to lock 
handle in place.

3

Write the name or type 
of wine on the label.

Installing wine label kit

7

Fit label over front edge of rack to 
match displayed wine.

8

Wipe the labels with a damp cloth 
to erase.

9

IMPORTANT!

Use spacer to correctly position cradle and avoid wine bottles being too upright resulting in 

bottles tipping over. 

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды